axis on中文是什么意思

發音:

中文翻譯
造句

軸開啟

axis n. ( pl. axes ) 1.軸，軸線。 2.【植 ...
in axis 自旋軸
on-axis (直接在音箱障板前的軸線上測出的)軸上; 同軸的
the axis 大戰期間與軸心國
anticlinal axis (saddle axis) 背斜軸
axis of symmetry;rotation-axis 對稱軸；旋轉對稱軸
drag axis of balance axis 天平阻力軸
hidden axis, invisible axis 暗軸
hidden axis,invisible axis 暗軸
a axis orientation a軸取向
a ci a axis 橫軸; 橫坐標軸
a-axis orientation a軸取向
abscissa axis 橫軸; 橫坐標軸
absorption axis 吸收軸
accessory axis 副軸
acoustic axis 聲軸
aerodynamic axis 空氣動力軸; 氣動軸
aileron axis 副翼樞軸
aiming axis 對準軸; 瞄準軸
alternating axis 交變軸; 交錯軸; 映轉軸
alttice axis 葉柵軸線
antenna axis 天線軸
anteroposterior axis y軸,前后軸,矢狀軸; 前后軸
anticlinal axis 背斜面軸; 背斜軸

"查查詞典"手機版

千萬人都在用的超大詞匯詞典翻譯APP

例句與用法

This rotation can be simplified by plotting the positions of the principal sections and principal axis on a stereographic net as described by jessop and wells from the rotations recorded .
按照杰索普和威爾士所論述的方法，根據記錄下來的轉動角，把主截面和主軸的位置畫到一個極射赤平投影網上，可使上述過程簡化。
Milling an elliptical - axis on nc lathe center
在車削加工中心實現橢圓軸的銑削加工
Draw the x axis and the y axis on the panel figure
在panel圖上繪制x坐標軸和y坐標軸。
Influences of transverse bias of arch axis on the arch ring behavior under static loads
拱軸線橫向偏離對拱圈靜力行為影響
Hence , large , long , and complex - shaped parts must be properly supported at critical positions to avoid sagging or preferably are hung with the long axis on the vertical
因此，對尺寸大，長度大，形狀復雜的部件，必須正確支撐其關鍵位置，以防產生弧垂，也可以將其長軸豎直懸掛。
If society were a train , the etiquette would be the rails along which only the train could rumble forth ; if society were a state coach , the etiquette would be the wheels and axis on which only the coach could roll forward
假定社會是一列火車，禮儀就好比軌道，火車只能沿著它隆隆前進；假定社會是一輛馬車，禮儀就好比輪子與軸，馬車只有靠它們才能滾滾前進。
The controlling force developed by the jets is working at the beginning of the initiative trajectory ( 0 . 385 - 3 . 385s ) to control the attitude of the projectile to keep its axis on the direction of launch - direction , so as to reduce the effect of initial disturbance
控制力由噴流作用力產生，在主動段的初始段( 0 . 385 3 . 385秒)控制彈體的姿態，使彈軸維持在初始方向上，從而減少初始干擾，減小落點散布(飛行時間約170秒) ，提高精度。
The influences of thermal effect of an axis on its design precision were discussed and the temperature distribution of a rotating axis was obtained by the conventional heat transfer equations that needed a complex solving procedure and gave a blurry distribution rule
摘要考慮了熱對提高軸類件設計精度的影響，并通過傳統導熱微分方程法和一般傳熱學理論對主軸在運動時熱分布進行了分析，指出了傳統熱微分方程解法復雜，從解析式中難以看出溫度分布規律，運用傳熱學理論解法簡單明? ，結果易于反映各參數關系，精確度較高，實用性強。